Skip to main content
X-VENTISO home

Searches every page and every manual, submittal and spec sheet on the site. Try XV250 weight, gas interlock or BACnet.

Damper Controls

For applications without a draft inducer

Stand-alone gas and solid fuel damper controls. When the chimney drafts on its own but the damper still has to be proven open, GFDC and SFDC do the job.

XV-GFDC gas damper control and XV-SFDC solid fuel damper control, each with its leads and power cord.
GFDC
Gas, interlocked
SFDC
Solid fuel, alarmed
Proves
Damper open
Wiring
Molex, plug-in

Gas

GFDC: Proven Open Before Ignition.

GFDC proves the damper open before the gas control can ignite. It is interlocked like every X-VENTISO gas controller: its damper proven relay sits in the appliance's ignition circuit, so if the damper does not prove open, the appliance does not light.

Connects to SIT Proflame 2 (terminal blocks factory-connected on the ignition lead), Dexen and Resideo / Honeywell modules, and to Robertshaw 780-715 U through the XV-IGN-ADPT-RS adapter. Home automation, a hearth remote receiver or a wall switch makes the call. When the call ends, the damper stays open for a 30-second post-purge, then closes.

XV-GFDC gas damper control with its damper lead, ignition lead and power cord.

Solid fuel

SFDC: Opened From the Wall, Alarmed if Not.

SFDC opens the automatic solid fuel damper from a wall switch in the room, and alarms if the damper does not prove open. The wall switch is by others: any single-pole switch, a hearth remote receiver or an automation relay, dry contact.

Leave the wall switch ON until the fire and all coals are completely out. Switching off closes the damper after a 30-second post-purge. Keep the XV-SFDC out of All Off, Away, Goodnight and scheduled-off automation scenes.

On power loss the damper springs open. The SFDC has no battery: connect it to a UPS (recommended) so the alarm stays active through an outage.

XV-SFDC solid fuel damper control with its damper lead, ignition lead and power cord.

In the box

What Ships, What You Add.

In the box

ControllerFactory-sealed, with a 6 ft power cord
Ignition lead4 ft, black 4-pin Molex. GFDC: two SIT Proflame 2 terminal blocks factory-connected
ManualXV-IM-DMP-CTRL installation manual

Sold separately

DamperGFDC: XV-GFD, XV-TMD or XV-INLD. SFDC: XV-SFD
SFDC wall switchBy others: any single-pole switch
ExtensionsXV-DAMPEREXT 20, 50 or 100 ft; XV-IGNEXT 20 or 50 ft
GFDC ignition adaptersXV-IGN-ADPT-RS (Robertshaw); XV-IGN-PFAK (automation on Proflame 2)
Several fluesXV-INTG: damper controls of the same fuel on one call

Specifications

Damper Control Specifications.

SpecificationGFDCSFDC
FuelGasSolid fuel
Call to runAppliance ignition control, automation, remote or switch: dry contactWall switch (by others), dry contact
Compatible dampersGas top-mount and inline (XV-GFD, XV-TMD, XV-INLD)Automatic solid fuel damper (XV-SFD)
Damper proven relayDry contact, 3 A @ 30 VDC, 3 A @ 250 VACNot used
Post-purge30 seconds after the call ends30 seconds after switch-off
AlarmDamper position: display and buzzer; the appliance stays offDamper position: display and buzzer
On power lossGas damper fails closed; the appliance cannot fireDamper springs open. No battery: UPS recommended
Designed forThe NFPA 54 vent damper interlock (12.15): the appliance cannot fire until the damper proves openNFPA 211 automatic dampers: a listed damper installed per its listing (9.9.4), operable from the room containing the fireplace (11.2.9.2)
Electrical rating120 VAC, 60 Hz, 1.0 A; 6 ft cord120 VAC, 60 Hz, 1.0 A; 6 ft cord
DisplayView-only, behind a clear protective coverView-only, behind a clear protective cover
Operating environment5 to 104°F (-15 to 40°C), non-condensing5 to 104°F (-15 to 40°C), non-condensing
EnclosureFactory-sealed, NEMA 1 (indoor). 5-1/8 x 9-3/8 x 3-1/8 in., surface mountSame
ListingsUL 508 Industrial Control · UL/ULC 378 Draft Equipment. ETL Listed, Intertek control no. 4007025UL 508 Industrial Control · UL/ULC 378 Draft Equipment. ETL Listed, Intertek control no. 4007025

Match the control to the damper. GFDC runs X-VENTISO gas dampers; SFDC runs the X-VENTISO solid fuel damper. Each damper fails the safe way for its fuel, so never pair a gas damper with SFDC or a solid fuel damper with GFDC.

Bench-tested before it is packed. Every X-VENTISO controller is tested on the bench before it ships: damper proving, the gas interlock on GFDC, and the alarm on SFDC. The serial number and the tester's initials are on every controller label.

Downloads

Documents and Drawings.

Bring us the project. We'll find the yes.